Monday, May 27, 2013

TONE CONTROL AND SUBWOOFER OUT



PT2350
is a tone control subwoofer cross-over low pass filter chip utilizing
CMOS Technology. It features a tone control range of 10dB (50Hz, 4
KHz) and subwoofer low pass filter of the second order Sallen Key
Design. The roll-off point can be adjusted by changing the value of the
external capacitor. Pin assignments and application circuits are
optimized for easy PCB Layout and cost saving advantages.


CMOS Technology


2-Channel Input
3-Channel Output (Including 1 stereo Output and Subwoofer Output)
Low Total Harmonic Distortion (THD<0.01%, Subwoofer THD<0.2%)
High S/N Ratio (S/N Ratio <-87dB, A-weighting)
Least External Components
Adjustment of Frequency response by changing the value of the external component
Single Power Supply: 3 to 8.5 Volts
Available in 20 pins, DIP or SO Package


PARTS
Resistors
2------ R1,R2--------------  --------- 10k / 1% / metal film
Capacitors
2------ C9,C10-------------    -------- 4.7nF / 63V / polyester
3------ C1,C7,C8--------   -------- --- 47nF / 63V / polyester
1------ C16----------------   --------- 100nF / 63V / polyester
1------ C13-----------------   -------- 220nF / 63V / polyester
2------ C3,C4-------------    --------- 2.2uF / 50V / polyester
5------ C5,C6,C11,C14,C15---       3.3uF / 100V / electrolytic
1------ C12-------------------------   - 10uF / 35V / electrolytic
1------ C17----------------- --------- 100uF / 16V / electrolytic
1------ C2---------------------------- 470uF / 35V / electrolytic
Integrated Circuits
1------ U1---------------------------- 78L08 / 8V voltage regulator / TO-92
1-------U2---------------------------- PT2350 / stereo tone control, subwoofer low pass filter IC / DIP20
Diodes
1------ D1---------------------------- 1N4153
Miscellaneous
1------ J1----------------------------- 2 pole wire connector (terminal block) to pcb / raster r. 5 mm / hight 9.7 mm
1------ P1----------------- ----------- 10k log stereo potentiometer / 6 mm saft
2------ P2,P3------------------------ 100k lin stereo potentiometer / 6 mm saft
5------ J2 to J5---------------------- RCA female to PCB, straight, Hosiden any colour


NOTICE ABOUT J2 to J18 . if you make one stereo input device you need 5 pcs of RCA female as listed in parts list
If you make 2 x 6 input device, you need total quantity of 15 pcs RCA female and also 2 x 6 changeover switch.
Code of J2 to J18 RCA female to PCB, straight, Hosiden, any colour
SW1 2 x 6 changeover High quality DIP rotary switch to PCB 2 x 6, Alcos witch DRS 2-6, 3.2mm saft


Frequency response of tone control unit is flat between 20 Hz … 20 kHz when treble and bass pots are in middle.
Overall gain is approx. 6 dB when treble and bass pots are in middle.
Treble and bass tone control range is approx. 10 dB (50Hz / 4 kHz) with given component values.
Subwoofer
cut off frequency can be adjusted by bass potentiometer… with component
values as listed above it is as follows : bass pot in minimum (left)
-3dB point, 240 Hz / -12dB 450 Hz, bass pot (middle) -3dB point 100 Hz
/-12dB 200 Hz, bass pot maximum (right) -3dB point 60 Hz / -12dB 120 Hz.
Distortion was < 0.1 % when input level was < 0.3V rms.
There
is no balance adjustment potentiometer in this application, if you need
balance, you must add it separately in this device.




DOWNLOAD PCB AND DATASHEET TONE CONTROL

No comments:

Post a Comment

Note: Only a member of this blog may post a comment.